Mouse β-actin (β-Actin) quantitative detection kit (ELISA) user's Guide ã€Kit name】 Mouse β-actin (β-Actin) quantitative detection kit (ELISA) ã€Use of the kit】 Quantitative detection of β-actin (β-Actin) in mouse serum, plasma and related liquid samples. ã€Detection principle】 This kit uses double antibody one-step sandwich enzyme-linked immunosorbent assay (ELISA). Add the standard, the sample to be tested, and the enzyme-labeled working solution to the transparent enzyme-labeled plate pre-coated with human plasma alpha particle membrane protein (GMP-140) antibody. After incubation for a sufficient time, wash to remove unbound components. . Add the developer A and B in turn. The developer (TMB) is converted into a blue product catalyzed by horseradish peroxidase (HRP), which turns yellow under the action of an acid. The concentration of plasma alpha particle membrane protein (GMP-140) is positively correlated. The OD value is measured at a wavelength of 450 nm. Based on the OD value of the standard and the sample, the content of human plasma alpha particle membrane protein (GMP-140) in the sample is calculated. ã€Composition of the kit】 1 Enzyme coated plate 12 holes × 8 7 Developer A liquid 6mL 2 Standard product: 240nmol / l 0.6mL 8 Developer B liquid 6mL 3 20 times concentrated washing liquid 25mL 9 Stop solution 6mL 4 Standard dilution 6mL 10 Instructions 1 serving 5 Sample diluent 6mL 11 Sealing film 2 sheets 6 Enzyme reagent 10mL 12 sealed bag 1 Remarks: The standard product is diluted with standard product diluent in order: 240, 120, 60, 30, 1.5, 7.5 nmol / l [Reagents and equipment needed but not provided] 1. 37 ℃ thermostat 2. Standard specification microplate reader 3. Precision pipettes and disposable tips 4. Distilled water 5. Disposable test tubes 6. Absorbent paper ã€Steps】 1. Preparation: Remove the reagent kit from the refrigerator and re-equilibrate at room temperature for 30 minutes. 2. Mixing solution: dilute the 20-fold concentrated washing solution with distilled water to the original one. 3. Add standard products and samples to be tested: take a sufficient number of enzyme-coated plates and fix them to the frame. Set up standard wells, sample wells to be tested and blank control wells, record the positions of each well in the standard wells. Add 50μL of the standard; add 10μL of the sample to be tested to the sample well, and then add 40μL of the sample diluent (that is, the sample is diluted 5 times); add 100μL of enzyme-labeled working solution to each well; no blank control well. 4. Incubation: Incubate in a 37 ° C water bath or thermostat for 60 minutes. 5. Wash the plate: discard the liquid, pat dry on the absorbent paper, fill each well with the washing liquid, let stand for 1min, shake off the washing liquid, pat dry on the absorbent paper, repeat the washing 5 times in this way Instructions for washing the board). 6. Color development: add 50 μL of developer A solution to each well, then add 50 μL of developer B solution, and develop color at 37 ° C in the dark for 15 min. 7. Termination: Remove the enzyme labeling plate and add 50μL of stop solution to each well to stop the reaction (the color changes from blue to yellow). 8. Determination: Zero the blank holes, and within 15 minutes after termination, measure the absorbance (OD value) of each well with a wavelength of 450 nm. 9. Calculation: According to the concentration of the standard product and the corresponding OD value, calculate the linear regression equation of the standard curve, and then calculate the corresponding sample concentration on the regression equation according to the OD value of the sample. You can also use various application software to Calculation. The final concentration is the actual measured concentration times the dilution factor. [Sample requirements] 1. The sample cannot contain sodium azide (NaN3) because sodium azide (NaN3) is an inhibitor of horseradish peroxidase (HRP). 2. The specimen should be extracted as soon as possible after collection. The extraction should be carried out according to relevant literature. The experiment should be carried out as soon as possible after extraction. If the test cannot be performed immediately, the specimen can be stored at -20 ℃, but repeated freezing and thawing should be avoided. 3. The sample should be fully centrifuged, without hemolysis and particles. ã€Precautions】 1. The experiment is carried out in strict accordance with the instructions, and the result of the experiment must be determined by the reading of the microplate reader. 2. If the enzyme-labeled coated board is not used up after opening, it should be put into a sealed bag and added with desiccant immediately. 3. It is recommended that all standards, samples and blank controls be tested in duplicate, and the average value is taken to reduce the experimental error. 4. If the color is too light, the substrate incubation time can be extended properly. 5. In order to avoid cross-contamination, the standard, sample and blank control should be replaced with a tip for each additional one; the common components such as enzyme working solution, sample diluent and substrate should be added by cantilever, and should not touch the microwell ; Do not reuse the sealing film. 6. The kits are used within the warranty period, and different batches of reagents should not be mixed. 7. Substrate B is sensitive to light and avoid prolonged exposure to light. [Summary of operating procedures] Prepare reagents, samples and standards Add the prepared samples, standards and enzyme standard working solution, and react at 37 ℃ for 60 minutes Wash the plate 5 times, add color developing solutions A and B, and develop at 37 ℃ for 15 minutes Add stop solution Read OD value within 15 minutes Calculation ã€examination range】 7.5-240 nmol / L ã€specification】 96 servings / box ã€Storage】 Store at 2-8 ℃, protected from light and moisture. ã€Validity】 6 months Shanghai Yuping Biological Technology Co., Ltd. specializes in selling ELISA kits of various brands and grades, with quality assurance and perfect after-sales service. And can be detected on behalf of free. Serving universities and immunology research units. Technicians serve you better.
In terms of shapes, sizes, and functions, a wide range of insulated water bottles made of stainless steel or food grade plastics, or tempered glass are available. We have double wall sport Plastic Water Bottle, single wall Stainless Steel Water Bottle, and double wall stainless steel water bottles, as well as high quality Tempered Glass Water Bottle, just like Swell bottles.
Features:
Food grade materials, like 18/8 stainless steel
Tight fitted lid keeps beverages hotter and colder than travel mugs, leakage proof
wide mouth accommodates full size ice cubes
compact design takes minimal space while maximizing capacity
sport drinking straw and handle
It is designed for sports, outdoors, on-the-go, travel, yoga, and hiking with sizes from 350ml Water Bottle to 2000ml vacuum Insulated Water Bottle; All of products are certified with FAD and LFGB.
Big welcome to you to visit our factory audited by BSIC and Wal-Mart. Pls contact us freely through on line or email. You would be satisfied with our prompt and professional service and response.
Water Bottle Water Bottle,Insulated Drinking Bottle,Copper Water Bottle,Stainless Steel Insulated Water Bottle Zhejiang Haoqi Industry And Trade Co.,Ltd. , https://www.anaturekitchen.com
Mouse β-actin (β-Actin) quantitative detection kit (ELISA)